Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 119

Page: 119 / 126

;---------------------------------------------------------------------

;SlotDefinition

;---------------------------------------------------------------------

SlotDefinition

Slot(1) = "Flow" 1 0,1 ;Default am zykl. Verkehr

Slot(2) = "Quantity net" 2 0,2,3 ;Default am zykl. Verkehr

Slot(3) = "Quantity forward" 0 0,4,5 ;Default nicht am zykl. Verkehr

Slot(4) = "Quantity reverse" 0 0,6,7 ; Default nicht am zykl. Verkehr EndSlotDefinition

GSD: Device database file

LSB: Least significant Bit

MSB: Most Significant Bit

PDM: Process Device Manager

PNO: PROFIBUS user organization

PROFIBUS PA: Process Fieldbus for Process Automation

Profibus Communication

B.9 Device Database File (GSD)

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

119

Summary of Contents for SITRANS F TRANSMAG 2































































































































Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews:

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 119 / 126

Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews: