manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 82 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 82

10.3

Error messages

Errors are indicated by a flashing "D" (Device error) or "F" (Measurement error) in the top right 
hand corner of the local display.

Table 10-2

Error messages  

Error

Diagnosis

Remedy

D

Flashing "D" in the top 
right hand corner of the 
display

General device error (see also section 
5.3.2)

Menu 2.1 Call device status

D

Device status (menu 2.1) 
"Memory failure"

Internal memory defective

Replace complete electronics

D

Device status (menu 2.1) 
"COM Module failure"

HART interface not available in the trans‐
mitter

Replace complete electronics

PROFIBUS interface not available in the 
transmitter

D

Device status (menu 2.1) 
"Software failure"

General software error

Do a restart (menu 6.4);
If error persists: have firmware reloaded (by serv‐
ice personnel), alternatively: replace complete 
electronics

D

Device status (menu 2.1) 
"Sensor failure"

Magnetic field current fuse defective

Change magnetic field current fuse (see section 
6.3.1)

Magnetic current cable defective (at ter‐
minals 5 and 6 in remote design)

Check cable and change if necessary

Magnet coil defective

Check on remote design:
Switch off device, disconnect magnetic field cur‐
rent cable, measure resistance at terminals 5 and 
6 on sensor: setpoint: 8 ... 20 Ω.
Otherwise: change sensor

Reference coil improperly connected (ter‐
minals 55, 66)

Check cable and replace if necessary

Electronics defective

Change complete electronics

D

Device status (menu 2.1) 
"Flow measurement dis‐
turbed"

No measurement possible (group mes‐
sage)

Change complete electronics

 

"SmartPLUG read failure"

Connected sensor without SmartPLUG or 
defective SmartPLUG

Check parameterization (range, unit etc.)
A correct measurement is still possible when the 
calibration values CFH and ZPH match the values 
on the rating plate of the sensor. 
Check whether this is the case and correct if nec‐
essary under the menus 6.7.2 and 6.7.3 

F

Flashing "F" in the top 
right hand corner of the 
display

General incorrect measurements, proc‐
ess errors or incorrect parameterization.

Menu 2.1 Call device status

Troubleshooting
10.3 Error messages

TRANSMAG 2 with MAG 911/E

82

Operating Instructions, 03/2021, A5E00102775-AC

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments