manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 19 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 19

Installing/mounting

4

SITRANS F flowmeters with minimum IP65/NEMA 4X enclosure rating are suitable for indoor and 
outdoor installations.

• Make sure that pressure and temperature specifications indicated on the device nameplate / 

label will not be exceeded.  

WARNING

Installation in hazardous location

Special requirements apply to the location and interconnection of sensor and transmitter. 
See Use in hazardous areas (Page 13) 

4.1

Installation safety precautions

WARNING

High pressure hazard

In applications with working pressures/media that can be dangerous to people, surroundings, 
equipment or others in case of pipe fracture, we recommend that special precautions such as 
special placement, shielding or installation of a pressure guard or a safety valve are taken when 
the flowmeter is mounted.       

4.2

Sensor installation

4.2.1

Determining a location

Note

The sensor must always be completely filled with liquid.   

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

19

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments