Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 32

Page: 32 / 126

4.4

Turning the local display

The local display can be turned in 90° steps to enable better reading in case of vertical installation
or overhead assembly.

1. Switch off the power supply.

2. Release the catch on the lid of the electronics compartment with a 3 mm Allen key.

3. Unscrew the cover.

4. Carefully release the fastening hooks of the local display using a screwdriver or similar tool

5. Pull out the unit, turn it to the desired position and push it back in.

6. Screw the lid back on and mount the lid catch.

①

Fastening hooks

Figure 4-19

Unlocking the fastening hooks on the local display

Installing/mounting
4.4 Turning the local display

TRANSMAG 2 with MAG 911/E

Operating Instructions, 03/2021, A5E00102775-AC

Summary of Contents for SITRANS F TRANSMAG 2































































































































Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews:

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 32 / 126

Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews: