manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 7 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 7

Introduction

1

1.1

Purpose of this documentation

These instructions contain all information required to commission and use the device. Read the 
instructions carefully prior to installation and commissioning. In order to use the device 
correctly, first review its principle of operation.

The instructions are aimed at persons mechanically installing the device, connecting it 
electronically, configuring the parameters and commissioning it, as well as service and 
maintenance engineers.

See also

Technical support (Page 122)

1.2

History

The contents of these instructions are regularly reviewed and corrections are included in 
subsequent editions. We welcome all suggestions for improvement.

The following table shows the most important changes in the documentation compared to each 
previous edition.

Edition

Remarks

03/2021

Explanation for ferrite beads, corrections regarding dimensions and EU directives

08/2010

TRANSMAG 2 Op. Instr.
• Information on the compact version was removed.

02/2009

TRANSMAG 2 Op. Instr.
• Restructering of contents.

02/2008

TRANSMAG
• All information concerning Intermag was removed.

02/2008

TRANSMAG / Intermag

1.3

Checking the consignment

1. Check the packaging and the delivered items for visible damages.

2. Report any claims for damages immediately to the shipping company.

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

7

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments