Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 22

Page: 22 / 126

4.2.2

Orienting the sensor

The sensor operates in all orientations, but Siemens has the following recommendations:

• Vertical installation with an upwards flow

Figure 4-4

Vertical orientation, upwards flow

NOTICE
Abrasive liquids / liquids containing solid particles

A vertical installation minimizes wear and deposits in the sensor

Note
Gas/air bubbles in the liquid

A vertical installation minimizes any negative effect of gas/air bubbles in the liquid

• Horizontal installation, terminal box upwards or downwards

Figure 4-5

Horizontal installation, various terminal box positions

NOTICE
Do NOT mount the sensor with the terminal box sideways

This will position the electrodes at the top where there is possibility for air bubbles and at
the bottom where there is possibility for mud, sludge, sand etc.

Note
Empty pipe detection

For applications with empty pipe detection, the sensor can be tilted 45°, as shown above.

Installing/mounting
4.2 Sensor installation

TRANSMAG 2 with MAG 911/E

Operating Instructions, 03/2021, A5E00102775-AC

Summary of Contents for SITRANS F TRANSMAG 2































































































































Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews:

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 22 / 126

Search results

Summary of Contents for SITRANS F TRANSMAG 2

Reviews: