15
[PRÉCAUTIONS DE CABLAGE]
[PRÉCAUTIONS DE CABLAGE]
AVERTISSEMENT
●
Assurez-vous de couper toutes les phases de l'alimentation externe avant d’essayer l'installation ou le
câblage. Faute de quoi, il y a risque d'électrocution ou d'endommagement du produit.
●
Assurez-vous d'attacher le couvercle de borne, fourni en tant qu'accessoire, avant d'alimentation ou
d'opération de lancement après installation ou câblage. Faute de quoi, il y a risque d'électrocution.
●
La température nominale du câble doit être de 80
ou plus.
●
Assurez-vous de bien câbler la plaque à bornes avec bride à ressort conformément aux précautions
suivantes. Faute de quoi, il y a le risque d’électrocutions, de pannes d'équipement, de court-circuit, de
rupture du fil, de dysfonctionnements ou de dommages au produit.
(1) La taille des extrémités du câble lors de la mise au rebut doit suivre les dimensions décrites dans
le manuel.
(2) Tordre les extrémités des fils échoués et s'assurer qu'il n'y a pas de fils lâches.
(3) Ne pas souder et plaquer les extrémités des fils électriques.
(4) Ne pas connecter plus que le nombre spécifié de fils ou fils électriques de taille non spécifiée.
(5) Fixez les fils électriques de sorte que ni le bornier ni les pièces connectées ne soient directement
soumis à une contrainte.
ATTENTION
●
Effectuer la mise à la terre classe D (résistance à la mise à la terre : 100
Ω
ou moins) de la borne de
mise à la terre sur le module CPU et les modules d'extension avec un fil de 2 mm
2
ou plus épais.
●
Connectez le câblage d’alimentation aux bornes dédiées décrites dans ce manuel. Quand
l’alimentation AC est connectée à une borne d'E/S ou à une borne d'alimentation DC, le contrôleur
programmable s’éteindra.
●
Ne pas câbler les bornes vides à l'extérieur. Cela pourrait endommager le produit.
●
Installer le module afin que la force excessive ne soit pas appliquée aux borniers, aux connecteurs
d'alimentation, aux connecteurs E/S, aux connecteurs de communication ou aux câbles de
communication. Faute de quoi, il y a risque d'endommagement ou de rupture ou de panne du
contrôleur programmable.
●
Assurez-vous d'observer les précautions suivantes afin d'éviter tout endommagement aux machines
ou les accidents dues au dysfonctionnement du contrôleur programmable causé par des données
anormales écrites sur le contrôleur programmable en raison d’effets du bruit.
(1) Ne pas regrouper la ligne d'alimentation, la ligne de commande et les câbles de communication,
ou ni les placer près du circuit principal, la ligne à haute tension, la ligne de charge ou la ligne
d’alimentation. À titre indicatif, posez la ligne d'alimentation, la ligne de commande et les câbles
de communication au moins à 100 mm du circuit principal, de la ligne à haute tension, de la ligne
de charge ou de la ligne d’alimentation.
(2) Effectuer la mise à la terre du blindage du câble E/S analogique sur un point du côté réception
des signaux. Toutefois, ne pas utiliser de mise à la terre commune avec des systèmes électriques
lourds.
●
Les câbles doivent être connectés après avoir vérifié le type de l’interface de connexion. Connecter
les câbles à une mauvaise interface ou connecter les câbles de façon incorrecte peut provoquer une
panne du module ou des dispositifs externes.
Summary of Contents for MITSUBISHI ELECTRIC MELSEC iQ-F FX5
