Sharp MX 3501N - Color Laser - Copier, Service Manual

Page: 234 / 448

MX3500N SIMULATION 7 – 126
62-12
Purpose Data clear
Function (Purpose) Used to set Enable/Disable of auto format
in HDD trouble.
* Be sure to format the HDD in FAT32.
Section MFP (HDD)
Item Clear
Operation/Procedure
1) When the machine enters the simulation, the screen on the
right is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK] button, [COLOR], or [BLACK] key is pressed, it is
highlighted and the current entered value is saved to EEPROM
and RAM.
<Descriptions of buttons, set range, and default values>
62-13
Purpose Data clear
Function (Purpose) Used to format the hard disk (operation
manual area only).
* Be sure to format the HDD in FAT32.
Section MFP (HDD)
Item Clear
Operation/Procedure
1) Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2) Press [YES] button.
3) The hard disk (operation manual area only) is formatted. [YES]
button is highlighted.
* When [NO] button or [EXECUTE] button is pressed, [EXE-
CUTE] button returns to the normal display, and [YES] and
[NO] buttons gray out.
* During formatting the hard disk (operation manual area
only), [EXECUTE] button is highlighted and "HDD FORMAT
(MANUAL AREA ONLY) EXECUTING..." is displayed.
* If formatting of the hard disk (operation manual area only) is
not completed normally, "HDD FORMAT (MANUAL AREA
ONLY) NG" is displayed.
* When formatting of the hard disk (operation manual area
only) is completed, [EXECUTE] button returns to the normal
display and [YES] and [NO] buttons gray out.
* When [CA] key or [SYSTEM SETTINGS] key is pressed to
exit the simulation, the machine is rebooted.
63
63-1
Purpose Adjustment/Setup/Operation data output/
Check (Display/Print)
Function (Purpose) Used to check the following values related
to shading for RGB and OC/RSPF/DSPF.
(3 x 2 = 6 kinds)
Section Scanner (Exposure)
Item Operation
Operation/Procedure
1) Select a color button to be displayed.
The shading set value of the selected button is displayed.
* When [B](Blue), [G](Green), or [R](Red) button is selected,
the selected button is highlighted and the adjustment value
of the selected color is displayed.
* Only one color button can be selected, and the selected but-
ton is highlighted. In the initial state, [B] is selected.
* If there is a page over [
↑
], an active display is shown and the
page moves up. If there is no page upward, the display
grays out and the operation is invalid.
If there is a page under [
↓
], an active display is shown and
the page moves down. If there is no page downward, the
display grays out and the operation is invalid.
* When [CLOSE] button is pressed, the display shifts to the copy
basic screen of simulation.
* Copying can be performed also by pressing [COLOR]/[BLACK]
key.
<Display item and description> (MX-3500N/4500N)
Item Content
Set
range
Default
value
A (0: YES,
1: NO) 0 Auto format Enable 0 to 1 1 (Disable)
1 Auto format Disable
CLOSE
A:
A 㧦 0
㧧 (0:YES 1:NO)
SIMULATION NO.62 㧙 12
AUTO FORMAT SETTING
㧔
HDD TROUBLE
㧕
0
㨇 0 㨪 1 㨉
OK
TEST
0
CLOSE
Display item Description Remark
GAIN ODD Gain adjustment value
(ODD)
GAIN EVEN Gain adjustment value
(EVEN)
OFFSET ODD Offset value (ODD)
OFFSET EVEN Offset value (EVEN)
SMP AVE ODD Reference plat sampling
average value (ODD)
SMP AVE EVEN Reference plat sampling
average value (EVEN)
TARGET VALUE Target value
BLACK LEVEL Black output level
ERROR CODE Error code (0, 1 to 4) 0: No error
1: STAGE1. Over the
loop number
2: STAGE2. The target
value is less than the
specified level.
3: STAGE3. The gain
set value is negative.
4: END is not
asserted.
RSPF WHITE
LEVEL 1ST First scan, RSPF white
reference level
CLOSE
A:
A 㧦 1
㧧 (0:YES 1:NO)
SIMULATION NO.62 㧙 12
AUTO FORMAT SETTING 㧔 HDD TROUBLE 㧕
1
㨇 0 㨪 1 㨉
OK
TEST
0
CLOSE