Scientific SM6026 User Manual Download Page 26

Page: 26 / 95

User Manual SM6026

3) Press STEP to set the sweep mode as single step sweep test mode.

3.4.2

FREQ (Hz)

This zone shows the currently swept parameter mode and its unit. What are right below this item are
parameters of the sweep list.

3.4.3

R[:] X[:]

This zone is the currently swept Function parameter and its unit. What are right below this item are the
sweep results.

3.4.4

CMP (Compare)

This zone indicates the compare results of the currently swept points. L means the result is lower than
the standard and H is higher than the standard, while blank is medium.

3.5 <MEASURE SETUP>

Press

[SETUP]

to enter into the

<MEASURE SETUP>

page shown as below:

In this page, the following control parameters can be set. (Items in parenthesis can be set)



Test function

(FUNC)



Test frequency

(FREQ)



Test level

(LEVEL)



Test range

(RANGE)



Test speed

(SPEED)



DC Bias

(DC BIAS)



Trigger Mode

(TRIG)



Auto Level Control

(ALC)



Delay Time

(DELAY)



Output Resistance

(Rsou.)



Average times

(AVG)



Voltage Level Monitor ON/ OFF

(Vm)



Current Level Monitor ON/ OFF

(Im)



Bias Current Isolation ON/ OFF

(ISO)



Deviation Test Mode A

(DEV A)

Summary of Contents for SM6026
































































































Search results

Summary of Contents for SM6026

Reviews:

Related manuals for SM6026

Brands by name

Popular brands

Scientific SM6026, User Manual

Search results

Summary of Contents for SM6026

Reviews:

Related manuals for SM6026

Brands by name

Popular brands