background image

User Manual SM6026

84

The CORRection:LENGth command is used to set the correction cable length. The CORRection:LENGth?
query returns the current set cable length.

Command syntax: CORRection:LENGth<value>

Where,

<value> is 0, 1, 2 or 4 followed by M.

For example: WrtCmd (“CORR:LENG 1M”) Set the cable length as 1 meter.

Query syntax: CORRection:LENGth?
Return format: <NR1><NL^END>

The CORReciton:METHod command is used to set the correction mode. The CORRection:METHod?
query returns the current correction mode.

Command syntax: CORRection:METHod

SINGle
MULTi

Where,

SINGle Set or return single channel mode.
MULTi Set or return multi channel mode.

For example: WrtCmd (“CORR:METH MULT”) Set the instrument as multi channel mode.

Query syntax: CORRection:METHod?
Return format:

SINGle

<NL^END>
MULTi

The CORReciton:OPEN command is used to execute open correction for 43 preset test points (SM6026
A has 41 preset test points).
Command syntax: CORRection:OPEN
For example: WrtCmd (“CORR:OPEN”)

The CORRection:OPEN:STATe command is used to set the open correction ON or OFF. The
CORReciton

OPEN:STATe? query returns the current open correction status.

Command syntax:

ON

CORRction:OPEN:STATe

OFF
1
0

Where,

1 (decimal 49) is equal to ON.
0 (decimal 48) is equal to OFF.

For example: WrtCmd (“CORR:OPEN: STAT ON”)

Query syntax: CORRection:OPEN:STATe?
Return format: <NR1><NL^END>

The CORRection:SHORt command is used to execute short correction for 43 preset test points (SM6026
A has 41 preset test points).

Command syntax: CORRection:SHORt
For example: WrtCmd (“CORR:SHOR”)

Summary of Contents for SM6026
































































































Reviews: