Scientific SM6026 User Manual Download Page 42 | Manualshive

Page: 42 / 95

background image

User Manual SM6026

42



OFF

This soft key is used to set the pass beep function OFF.

4.1.2

FAIL BEEP

This zone is used to control and display the beep mode as

FAIL BEEP

when the test result is unqualified.

Operation steps for setting

FAIL BEEP

1) Move the cursor to FAIL BEEP, the following soft keys will be displayed.



HIGH LONG

This soft key is used to select high and long beep.



HIGH SHORT

This soft key is used to select high and short beep.



LOW LONG

This soft key is used to select low and short beep.



TWO SHORT

This soft key is used to select two low and short beeps.



OFF

This soft key is used to set the fail beep mode OFF.

4.1.3

LANGUAGE

This zone is used to control and display the current language mode of the operating instrument.

Operation steps for setting language

:

1) Move the cursor to LANGUAGE, the following soft keys will be displayed.



ENGLISH

This soft key is used to select English as the operation language.



CHINESE

This soft key is used to select Chinese as the operation language.

4.1.4

PASS WORD

This zone is used to display the password–protection mode.

Operation steps for setting the password

:

1) Move the cursor to PASS WORD, the following soft keys will be displayed.



OFF

This soft key is used to turn off the password protection mode.



Hold SYSTEM

This soft key is used to turn on the password protection function including file protection

and starting up password.



Hold FILE

This soft key is used to protect user’s file.



MODIFY

This soft key is used to modify the password. The operation steps are as follows:
Press MODIFY to input a new password. After inputting, the prompt information will
appear on the screen to prompt you to confirm the new password. Input the new
password again till the modification finishes.

————————————————————————————————————————————

Note

: The default password is 2827.

————————————————————————————————————————————

«
...
40
41
42
43
44
...
»

Summary of Contents for SM6026
































































































Reviews:

No comments

Related manuals for SM6026

Brand: Teledyne Analytical Instruments Pages: 107

Brand: Macnaught Pages: 8

Brand: H-Star Pages: 36

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

iNELS Air AirCFS-100S

Brand: Elko Pages: 4

Brand: PCE Health and Fitness Pages: 7

Brand: NIEUWKOOP Pages: 2

Micro Alti Vario Plus

Brand: Fairhaven Pages: 20

Brand: Xsens Pages: 12

BioTector B3500C

Brand: Hach Pages: 165

Brand: Fora Pages: 10

Brand: Bamo Pages: 2

Druck DryTC 165

Brand: Baker Hughes Pages: 130

Brand: Samson Pages: 28

Brand: Polaroid Pages: 60

wtw Cleaning Air Box -115 VAC

Brand: Xylem Pages: 32

Brand: Keysight Technologies Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands