Scientific SM6026 User Manual Download Page 13

Page: 13 / 95

User Manual SM6026

7) Power socket

Input AC power.

8) Nameplate

Information about production date, instrument number and
manufacturer etc..

Warning !

Be sure that the direction of fuse is accordant with power-supply voltage range before charging.

2.3 Display zone

SM6026 applies a 65k, 4.3-inch TFT display. The display screen is divided into the following zones:

Fig 2-3 Display Zones

1) Display page name

Indicate the name of the currently displayed page.

2) Soft keys

The zone is used to display the function definition of soft key.
The definition of soft key can be different as the difference of
cursor’s

direction in the zone.

3) Test result/ condition display zone :

In this zone, test result information and current condition are
displayed.

4) Help

In this zone, information about system and user data input is
displayed.

2.4 Main menu keys and corresponding displayed pages

2.4.1

[MEAS]

When the LCR function is active, press this key-[MEAS] to enter into the LCR measurement display page,
the following soft keys will be displayed in the soft key zone.

Summary of Contents for SM6026
































































































Search results

Summary of Contents for SM6026

Reviews:

Related manuals for SM6026

Brands by name

Popular brands

Scientific SM6026, User Manual

Search results

Summary of Contents for SM6026

Reviews:

Related manuals for SM6026

Brands by name

Popular brands