Scientific SM6026 User Manual Download Page 74 | Manualshive

Page: 74 / 95

background image

User Manual SM6026

74

The FUNCtion:IMPedance command is used to set instrument functions. The FUNCtion:IMPedance?
query returns the current function parameters.

Command syntax: FUNCtion:IMPedance <function>
<function> can be one of the following items.
CPD

Set the function as Cp-D

LPRP

Set the function as Lp-Rp

CPQ

Set the function as Cp-Q

LSD

Set the function as Ls-D

CPG

Set the function as Cp-G

LSQ

Set the function as Ls-Q

CPRP Set the function as Cp-Rp

LSRS

Set the function as Ls-Rs

CSD

Set the function as Cs-D

RX

Set the function as R-X

CSQ

Set the function as Cs-Q

ZTD

Set the function as Z-θ◦

CSRS Set the function as Cs-Rs

ZTR

Set the function as Z-θr

LPQ

Set the function as Lp-Q

GB

Set the function as G-B

LPD

Set the funxtion as Lp-D

YTD

Set the function as Y-θ◦

LPG

Set the function as Lp-G

YTR

Set the function as Y-θr

For example: WrtCmd (“FUNC:IMP RX”) Set the function as R-X.

Query syntax: FUNCtion:IMPedance?
Return format: <function><NL^END>

The FUNCtion:IMPedance:RANGe command is used to set the range. The
FUNCtion:IMPedance:RANGe? query returns the current range.

Command syntax: FUNCtion:IMPedance:RANGe <value>
Where, <value> can be the impedance of the DUT or NR1, NR2 or NR3 data
format followed by OHM or KOHM.
For example: WrtCmd (“FUNC:IMP:RANG 1KOHM”) Set the range as 1kOHM.

Query syntax: FUNCtion:IMPedance:RANGe?
Return format: <value><NL^END>
Where, <value> can be
10

30

100

300

1000

3000

10000 30000 100000

The FUNCtion:IMPedance:RANGe:AUTO command is used to set the automaticrange selection status.
The FUNCtion:IMPedance:RANGe:AUTO? query returns the current range status.
Command syntax:

ON (1)

FUNCtion:IMPedance:RANGe:AUTO

OFF (0)

Where,

Character 1 (49) is equal to ON.
Character 0 (48) is equal to OFF.

For example: WrtCmd (“FUNC:IMP:RANG:AUTO ON”) Set the automatic range as ON.

Query syntax: FUNCtion:IMPedance:RANGe:AUTO?
Return format: <NR1><NL^END>

The FUNCtion:Source MONitor:VAC command is used to set the voltage monitor ON or OFF. The
FUNCTtion:Source MONitor:VAC? query returns the current voltage monitor status.

«
...
72
73
74
75
76
...
»

Summary of Contents for SM6026
































































































Reviews:

No comments

Related manuals for SM6026

Brand: ABB Pages: 20

Brand: Utilitech Pages: 2

Brand: OHAUS Pages: 84

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: TA Instruments Pages: 7

Brand: YOKOGAWA Pages: 53

Brand: QEED Pages: 6

Level Pro UltraPro 500 Series

Brand: Icon Process Controls Pages: 19

Brand: LaserLiner Pages: 80

PASPORT PS-2174

Brand: PASCO Pages: 4

Brand: Unipro Pages: 2

Brand: Xylem Pages: 39

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: T&D Pages: 31

Sonic-Pro S6A Series

Brand: Blue-White industries Pages: 2

Brand: FMT Swiss AG Pages: 24

Roast Alert/3 ET-8C

Brand: Redi-Chek Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands