Sapling Saw 4 Installation Manual Download Page 53

Page: 53 / 114

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Dual-mount pole, including
mounting plate.

#8-32x7/16 screw

M3.5-1.0x10 screw (black)

Internal-tooth washer

#10-32x3/8 green screw

#6-32x1 screw

(4 used)

(not used)

(4 used)

Flag Mount Installation - Square Clock - Locally Powered

Description

SAW square analog clock

Quantity

Picture

Included in Package

Included in Pole Kit (SAB-4GD-00S-0)

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

Continued on next page

VERY IMPORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL OR HOUSING. REFER TO THE
SYNCHRONIZATION SYSTEM SETUP SECTION OF THIS MANUAL FOR INSTRUCTIONS.

The Clock and all network equipment must be powered and configured before you install the clock. If the network equipment is not

properly installed and powered, and if the clocks have not been configured to communicate with the network equipment, the clocks will not

synchronize.

Summary of Contents for Saw 4



















































































































Search results

Summary of Contents for Saw 4

Reviews:

Related manuals for Saw 4

Brands by name

Popular brands

Sapling Saw 4, Installation Manual

Search results

Summary of Contents for Saw 4

Reviews:

Related manuals for Saw 4

Brands by name

Popular brands