Sapling Saw 4 Installation Manual Download Page 28

Page: 28 / 114

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Description

SAW square analog clock

Mounting Piece

(already attached to

clock housing)

Quantity

Picture

Wall Mount Installation - Square Clock - Locally Powered

PLEASE NOTE:

A user will also have to provide a Phillips-head screwdriver, a small flat-blade screwdriver, a single gang box, any equipment needed to install

the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a
replacement kit.

Power/grounding wires

And connector

#8x1.5 Self-tapping screw

Wall anchor

(not used)

Included in Package

Included in Wiring Kit (A-WK-12-1V)

VERY IMPORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL OR HOUSING. REFER TO THE
SYNCHRONIZATION SYSTEM SETUP SECTION OF THIS MANUAL FOR INSTRUCTIONS.

The Clock and all network equipment must be powered and configured before you install the clock. If the network equipment is not

properly installed and powered, and if the clocks have not been configured to communicate with the network equipment, the clocks will not

synchronize.

Included in Gang Box Kit (A-GB-MK-1)

#6-32x1 screw

#6-19x3/8 screw

Summary of Contents for Saw 4



















































































































Search results

Summary of Contents for Saw 4

Reviews:

Related manuals for Saw 4

Brands by name

Popular brands

Sapling Saw 4, Installation Manual

Search results

Summary of Contents for Saw 4

Reviews:

Related manuals for Saw 4

Brands by name

Popular brands