manualshive.com logo in svg

Ross NK Routing Systems RCP-QE, User Manual, Page: 25 / 68

Share
Download
Ross NK Routing Systems RCP-QE User Manual Download Page 25

RCP-QE User Guide (v02)

Setting Up the RCP-QE • 4–5

The 

Panel Configuration

 editor opens.

Figure 4.5  

The RCP-QE Panel Configuration editor tab in DashBoard

RCP-QE Panel Configuration Editor Field Descriptions

General

Serial Num

 (read-only) – the serial number is set in the factory before shipping and is unique to each device. This 

parameter is not user configurable.

Version

 (read-only) – the software/firmware version.

Device Details

Name

 – this field can be assigned by the user to uniquely name an RCP-QE.

This field has a maximum of 16 characters and is used for description and identification only.

Group

 – a group number can be assigned by the user to organize devices into groups. For example, users can assign 

separate group numbers for devices in different physical areas.

This field has a maximum of 10 characters and by default is blank.

Details

 – assigned by the user to give an RCP-QE specific details. For example, a physical location or a brief 

description of its use.

This field has a maximum of 16 characters and is used for description and identification only.

Address

 – this address is used within the overall control system to identify NK devices using resource management 

and protects. Each device must be given a unique T-BUS address to avoid communication conflicts

1

.

The valid value range for assigning an individual device T-BUS address is 1-255.

1. Except when panel-linking is used.

Summary of Contents for NK Routing Systems RCP-QE





































































Reviews:

No comments