manualshive.com logo in svg

Ross NK Routing Systems RCP-QE, User Manual, Page: 15 / 68

Share
Download
Ross NK Routing Systems RCP-QE User Manual Download Page 15

RCP-QE User Guide (v02)

Installation • 3–1

Installation

Unpacking the Equipment

On receiving your RCP-QE, check the contents against the packing list. Before you start installing the RCP-QE into 
your system, ensure that all equipment itemized on the packing list is present and that there are no signs of damage.

If anything is missing or damaged, contact your Ross Video office immediately to obtain the correct warranty 
service procedures. This ensures prompt assistance, minimal turnaround time, and avoids any freight issues.

We recommend that the equipment is installed to any relevant standards and approvals by qualified and experienced 
personnel.

General

These installation guidelines assume the following:

• The relevant NK Series equipment has been installed into a ventilated rack frame. The relative humidity in the 

environment of the equipment should be < 70% (non-condensing).

• The routing switcher system has been well planned and designed. Consideration must be given to inputs and 

outputs across multiple router levels and typical operating scenarios for breakaways.

• Where required, correct IP addresses have been assigned to the equipment.
• The routing switchers are connected to physical inputs and outputs and have appropriate power supplies.

Installing the RCP-QE

The RCP-QE is powered using the 5 V 2 A power supply provided. This power supply connects directly to the AC 
mains supply.

Warning

 — Ensure that the AC mains supply complies with the PSU specification 

before making the connection.

Warning

 — An earthed neutral mains supply and residual current device is 

recommended for safe operation.

Summary of Contents for NK Routing Systems RCP-QE





































































Reviews:

No comments