Rosemount P330 Installation And Operation Manual Download Page 83

Page: 83 / 92

9-3

Specifications and Reference Data

Power Management

Auto power OFF, auto backlight OFF, battery low indicator, and status
on key press.

Remote Pressure Sensors
(External Transducers)

Programmable for up to ten digitally
characterized sensors.

Remote Sensor Media

316 SST and Hastelloy C

compatibility.

Maximum Working Pressure

Two times the full scale for ranges up to
1000 psi (69 bar).

1.2 times the full scale for ranges 1000 psi
(69 bar) and above.

Burst Pressure

Four times the full scale for ranges up to
500 psi (34 bar).

20000 psi (1380 bar) for ranges 1000 psi (69 bar) and above.

Environmental
Specifications

Display

Panel

2.36 × 2.36 in. (6 × 6 cm) graphic LCD
with backlight.

Readout

± 99999 capability, 2 readings per second.

Temperature

Operating: 15 to 120 °F (–9.4 to 49 °C).

Calibrated: 15 to 105 °F (–9.4 to 40.6 °C).

Humidity

0 to 90% non-condensing.

Enclosure Rating

NEMA 12 (IP54).

Summary of Contents for P330





























































































Search results

Summary of Contents for P330

Reviews:

Rosemount P330, Installation And Operation Manual, Page: 83 / 92

Search results

Summary of Contents for P330

Reviews: