manualshive.com logo in svg

Rosemount P330, Installation And Operation Manual, Page: 15 / 92

Share
Download
Rosemount P330 Installation And Operation Manual Download Page 15

2-3

Hardware Functions

To install either the rechargeable NiCad pack or six C cell batteries, 
proceed as follows:

1. Ensure that the validator is turned off.

2. Unscrew the battery compartment cover and remove it.

3. If there are batteries in the compartment, carefully lift them out.

4. Fit new batteries or a battery pack into the compartment aligned 

as shown in Figure 2-1. 

5. Replace the cover and tighten the screws.

Charging the NiCad Battery 
Pack

To charge the NiCad battery pack, proceed as follows: 

1. Plug the ac power adapter/charger unit into the dc power input on 

the external interface panel (see Figure 2-4 on page 2-7). 

2. Plug the ac power adapter/charger unit into an ac power supply.

3. Turn the validator on, and let it charge for 14 hours for a fully 

recharged battery.

See Safety Messages on page 2-1 for complete warning information.

Summary of Contents for P330





























































































Reviews:

No comments