Rosemount P330 Installation And Operation Manual Download Page 38

Page: 38 / 92

Rosemount Model P330 Pressure Validator

4-8

Setting units in any task mode other than Basic or Advanced

1. Press the

OUTPUT

key.

2. Use

and

to highlight

UNITS

. Press

ENTER

3. Use

and

to highlight desired units. Press

ENTER

4. If desired units are not listed, refer to Selecting Units on page

4-4.

Setting units in Basic mode

1. Press

2. Use

and

to highlight

UNITS

. Press

ENTER

3. Use

and

to highlight desired units. Press

ENTER

4. If desired units are not listed, refer to Selecting Units on page

4-4.

Setting units in Advanced mode

1. Press the

OUTPUT

key.

2. Press

3. Use

and

to highlight

UNITS

. Press

ENTER

4. Use

and

to highlight desired units. Press

ENTER

5. If desired units are not listed, see Selecting Units on page 4-4.

Zeroing the Display

Both the input and the output displays should be set to zero before a
validation.

NOTE

If the display is more than 5% of zero and an attempt is made to zero it,
the screen displays the message

ZERO TOO LARGE

, and the display will

not zero. Turn the release valve counterclockwise to make sure the
system is depressurized.

To zero the input and output displays, press the shaded keys in Figure
4-10, and proceed as follows:

FIGURE 4-10. Zeroing the Input and
Output Displays.

Summary of Contents for P330





























































































Search results

Summary of Contents for P330

Reviews:

Rosemount P330, Installation And Operation Manual, Page: 38 / 92

Search results

Summary of Contents for P330

Reviews: