manualshive.com logo in svg

Rockwell Automation 2080-L50E-24AWB, User Manual, Page: 360 / 390

Share
Download
Rockwell Automation 2080-L50E-24AWB User Manual Download Page 360

360

Rockwell Automation Publication 2080-UM002N-EN-E - November 2022

Appendix H          User-defined Function Block Motion Instructions

raC_UDT_Itf_K5100_Cmd

raC_UDT_Itf_K5100_Cmd is the User-Defined Data Type for device commands. Its members 

provide application program access to common basic device commands.

Table 105

 shows member names, descriptions, and tag data types.

All the commands are available whether operating the device physically or virtually.

While it is possible, it is not typical to modify any of these UDT values directly. The Motion 

Operation UDFBs manipulate these values as a result of their operation.

raC_UDT_Itf_K5100_Sts

raC_UDT_Itf_K5100_Sts is the User-Defined Data Type for device status. Its members provide 

application program access to device states, status, and diagnostic data. The following table 

shows member names, descriptions, and tag data types.

CamExecutionSchedule

Future: Determines the method used to execute the CAM 

profile.

DINT

CamExecutionMode

Future: Determines if the cam profile is executed only one 

time or repeatedly.

DINT

CamStopMode

Future: Determines the stop mode of CAM.

BOOL

CamSlaveScaling

Future: Scales the total distance covered by the slave axis 

through the cam profile.

DINT

CamLockPosition

Future: Determines the starting location in the cam profile

DINT

CamMasterLockPosition

Future: Determines the master location where the slave axis 

locks to the mater axis.

DINT

CamMasterLeadingCounts

Future: Determines the leading counts (master axis) before 

the cam profile is executed.

DINT

CamMasterUnlockCounts

Future: Determines the unlock counts (master axis) when the 

cam profile is executed.

DINT

CamMasterCyclicLeadingCounts

Future: Determines the cyclic leading counts (master axis) 

during the cam profile is executed.

DINT

GearRatioSlaveCounts

Integer value representing slave counts. This value is P1.044 

Gear Ratio Follower Counts from the E-gear ratio in 

KNX5100C software.

DINT

GearRatioMasterCounts

Integer value representing master counts. This value is 

P1.045 Gear Ratio Master Counts from the E-gear ratio in 

KNX5100C software. 

DINT

Table 105 - raC_UDT_Itf_K5100_Cmd Data Types

Member

Description

DataType

bCmd

Commands (Bit Overlay)

DINT

Physical

1 = Operate as a physical device

BOOL

Virtual

1 = Operate as a virtual device

BOOL

ResetWarn

1 = Reset device warning

BOOL

ResetFault

1 = Reset device trip or fault

BOOL

Activate

1 = Activate Output Power Structure

BOOL

Deactivate

1 = DeActivate Output Power Structure

BOOL

StartMotion

A zero-to-one transition means the motion command is 

issued from the external controller.

BOOL

StopMotion

A zero-to-one transition will stop any active motion 

command in the drive.

BOOL

Table 104 - raC_UDT_Itf_K5100_Set Data Types (Continued)

Member

Description

DataType

Summary of Contents for 2080-L50E-24AWB







































































































































































































































































































































































































Reviews:

No comments