manualshive.com logo in svg

Rockwell Automation 2080-L50E-24AWB, User Manual, Page: 138 / 390

Share
Download
Rockwell Automation 2080-L50E-24AWB User Manual Download Page 138

138

Rockwell Automation Publication 2080-UM002N-EN-E - November 2022

Chapter 8          EtherNet/IP Network

Predefined Tags in 

PowerFlex 520-series and 

Kinetix 5100 Drives

With Connected Components Workbench software version 21 or later, when Kinetix 5100 and 

PowerFlex 520 series products are added into the Micro800 controller (with firmware revision 

21 or later) project under the Ethernet-Module tree, predefined tags are made available in the 

Connected Components Workbench software to help you program the logic easily.

The Input and Output assembly are shown here for your convenience. While you can directly 

manipulate these assemblies, they rely on your logic to operate correctly, including timing, 

pre-existing drive conditions, and so on. It is typical to use the predefined Motion Operation 

UDFBs to perform motion operations.

Table 17 - Kinetix 5100 Motion Drive Input Assembly Data

Name

Data Type Description

Value

Comment

InfoBits

SINT

InfoBits.0

BIT

Indicates whether the drive is in run mode.

0 = Drive is idle

1 = Drive is in run mode

RunMode

InfoBits.1

BIT

Indicates whether the connection is faulted.

0 = Connection is not faulted

1 = Connection is faulted

ConnectionFaulted

InfoBits.2

BIT

Indicates whether the diagnostic is active.

0 = Diagnostic is not active

1 = Diagnostic is active

DiagnosticActive

DiagnosticSequenceCount

SINT

The sequence count for the diagnostic.

DataBits

SINT

DataBits.1

Bit

Indicates whether the drive is in a faulted state.

0 = No Fault

1 = Faulted

Fault

DataBits.2

BIT

Indicates whether the data validity is questionable.

0 = Data is valid

1 = Date validity is questionable

Uncertain

StatusBits

SINT

Indicates whether the drive is in a warning state.

0 = No warnings

1 = Drive is in a warning state

StatusBits.1

BIT

Indicates whether the motor is enabled.

0 = Motor is not enabled

1 = Motor is enabled

WarningPresent

StatusBits.2

BIT

Indicates whether the motor is ready to be enabled.

0 = Motor is not ready

1 = Motor is ready

Active

StatusBits.3

BIT

Indicates whether the drive received the command 

from the controller.

Indicates that the new command has 

been received by the K5100 drive. It 

toggles between 0 and 1 after a new 

command has been received by the 

K5100 drive. When this bit toggles, it 

stays at the toggled state until a new 

command is received.

Ready

StatusBits.4

BIT

Indicates whether the drive completed the home 

operation.

1 = Drive completed the home operation CommandinProgress

StatusBits.5

BIT

Indicates whether the motor is stopped.

1 = Motor is stopped

HomedStatus

StatusBits.6

BIT

Motor actual at reference (position, speed, torque) 

based on mode.

1 = Motor actual at reference (position, 

speed, torque) based on mode

Stopped

StatusBits.7

BIT

AtReference

OperatingMode

SINT

Indicates the drive operation mode.

-128…-1 = Reserved

0 = Mode not specified

1 = Position mode

2 = Speed mode

3 = Home mode

4 = Torque mode

5 = Gear mode

6 = Index mode

7…127 = Reserved

ActiveIndex

SINT

Indicates the currently executing index (PR).

-128…-1 = Reserved

0 = PR 0: Homing

1…99 = PR 1…PR 99

100…127 = Reserved

MotorType

SINT

Indicates which type of motor is connected to the 

drive.

0 = No motor connected

1 = Rotary motor connected

2 = Linear motor connected

ActualSpeed

DINT

Motor actual velocity.

A valid value in RPM.

FaultCode

INT

Fault code.

For more information, see the Kinetix 

5100 EtherNet/IP Indexing Servo Drives 

User Manual, publication 

2198-UM004

.

WarningCode

INT

Warning code.

Summary of Contents for 2080-L50E-24AWB







































































































































































































































































































































































































Reviews:

No comments