manualshive.com logo in svg

Rockwell Automation 2080-L50E-24AWB, User Manual, Page: 139 / 390

Share
Download
Rockwell Automation 2080-L50E-24AWB User Manual Download Page 139

Rockwell Automation Publication 2080-UM002N-EN-E - November 2022

139

Chapter 8          EtherNet/IP Network

ActualPosition

DINT

Actual position of the motor.

PUU (counts or user units)

AcutalTorque

DINT

Actual torque of the motor.

% motor rated torque

ParamterMonitor1Value

DINT

Parameter monitor selection 1.

0 = No parameter is selected

0x0001…0xFFFF = returned value that is 

mapped from KNX5100C Function List > 

Parameter Editor > StatusMonitor ID060

ParamterMonitor2Value

DINT

Parameter monitor selection 2.

1 = No parameter is selected

0x0001…0xFFFF = returned value that is 

mapped from KNX5100C Function List > 

Parameter Editor > StatusMonitor ID061

ParamterMonitor3Value

DINT

Parameter monitor selection 3.

2 = No parameter is selected

0x0001…0xFFFF = returned value that is 

mapped from KNX5100C Function List > 

Parameter Editor > StatusMonitor ID062

ParamterMonitor4Value

DINT

Parameter monitor selection 4.

3 = No parameter is selected

0x0001…0xFFFF = returned value that is 

mapped from KNX5100C Function List > 

Parameter Editor > StatusMonitor ID063

ParamterMonitor5Value

DINT

Parameter monitor selection 5.

4 = No parameter is selected

0x0001…0xFFFF = returned value that is 

mapped from KNX5100C Function List > 

Parameter Editor > StatusMonitor ID064

Table 17 - Kinetix 5100 Motion Drive Input Assembly Data (Continued)

Name

Data Type Description

Value

Comment

Table 18 - Kinetix 5100 Motion Drive Output Assembly Data

Name

Data Type Description

Value

Comment

OperatingMode

SINT

This enumerated value indicates the drive's internal 

mode setting. The drive can operate in different 

submodes while in IO Mode.

-128…-1 = Reserved

0 = Mode not specified

1 = Position mode

2 = Speed mode

3 = Home mode

4 = Torque mode

5 = Gear mode

6 = Index mode

7 = ECAM mode

8…127 = Reserved

ServoControl

SINT

ServoControl.0

BIT

A transition from 0 to 1 enables the motor.

ServoOn

ServoControl.1

BIT

A transition from 0 to 1 disables the motor.

ServoOff

ServoControl.2

BIT

A transition from 0 to 1 stops motion on the motor.

StopMotion

ServoControl.3

BIT

A transition from 0 to 1 clears an active drive fault.

FaultReset

ServoControl.4

BIT

A transition from 0 to 1 means that the motion 

command is issued from the external controller.

StartMotion

HomingMethod

SINT

The method of Homing.

For more information, see the Kinetix 

5100 EtherNet/IP Indexing Servo Drives 

User Manual, publication 

2198-UM004

.

SpeedReference

DINT

The commanded speed for the motor.

Units are in 0.1 RPM

-80000…+80000

1…20000 (home mode)

AccelReference

DINT

The commanded acceleration rate for the motor.

Units are in 0.1 RPM/sec

DecelReference

DINT

The commanded deceleration rate for the motor.

Units are in 0.1 RPM/sec

PositionReference

DINT

The commanded position used for indexing.

The scaling relationship from the E-gear 

ratio in KNX5100C software defines the 

User units.

HomeReturnSpeed

DINT

The return speed when home mode is the operating 

mode.

Units are in 0.1 RPM (rotary motors)

1…5000

NonCyclicMoveType

SINT

Enumerated value used to determine the noncyclic 

move type.

-128…-1 = Reserved

0 = Absolute

1 = Relative

2 = Incremental

3 = High-speed capture

4…127 = Reserved

Summary of Contents for 2080-L50E-24AWB







































































































































































































































































































































































































Reviews:

No comments