manualshive.com logo in svg

Rockwell Automation 2080-L50E-24AWB, User Manual, Page: 183 / 390

Share
Download
Rockwell Automation 2080-L50E-24AWB User Manual Download Page 183

Rockwell Automation Publication 2080-UM002N-EN-E - November 2022

183

Chapter 9          Motion Control

Limits

Edit the Limits parameters based on the table below.

Table 30 - Motor and Load Parameters

Parameter

Description and Values

User-defined Unit

Defines user unit scaling that matches your mechanical system values. These units 

shall be carried forward into all command and monitor axis in user unit values 

throughout programming, configuration, and monitoring functions. 

Position

Select from any of the following options:

– mm

– cm

– inches

– revs

– custom unit (ASCII format of up to 7 characters long)

Time

Read only. Predefined in seconds.

Motor Revolution

Defines pulse per revolution and travel per revolution values.

Pulse per Revolution

(1)

(1) The parameter is set as REAL (float) value in Connected Components Workbench. To learn more about conversions and 

rounding of REAL values, see 

Real Data Resolution on page 187

.

Defines the number of pulses needed to obtain one revolution of the drive motor. 

Range

: 0.0001…8388607

Default

: 200.0

Travel per Revolution

(1)

Travel per revolution defines the distance, either linear or rotational, that the load 

moves per revolution of the motor.

Range

: 0.0001…8388607. 

Default

:1.0 user unit.

Direction

Defines polarity, mode, and change of delay time values.

Polarity

Direction polarity determines whether the direction signal received by the 

controller as a discrete input should be interpreted on the input as received by the 

motion controller, (that is, the non-inverted case), or whether the signal should be 

inverted prior to interpretation by the motion control logic.

Set as Inverted or Non-inverted (default).

Mode

Set as Bi-directional (default), Positive (clockwise), or Negative (counter-clockwise) 

direction.

Change Delay Time

Configure from 0…100 ms.

Default value is 10 ms.

A red border on an input field indicates that an invalid value has been 

entered. Scroll over the field to see tooltip message that will let you know 

the valid value range for the parameter. Supply the valid value. 

ATTENTION: 

Modifying Motor Revolution parameters may cause axis 

runaway.

ATTENTION: 

To learn more about the different types of Limits, see 

Limits on 

page 172

.

Summary of Contents for 2080-L50E-24AWB







































































































































































































































































































































































































Reviews:

No comments