Rockwell Automation 2080-L50E-24AWB User Manual Download Page 177

Page: 177 / 390

Rockwell Automation Publication 2080-UM002N-EN-E - November 2022

177

Chapter 9 Motion Control

MC_MoveAbsolute function block to an axis with too short a distance given when the

axis is moving.

• When one movement function block is issued to an axis, and the axis is in the Stopping

or Error Stopping sequence.

For the above exceptions, it is still possible for the user application to issue a successful

movement function block to the axis after the axis state changes.

MC_Engine_Diag Data Type

The MC_Engine_Diag data type contains diagnostic information on the embedded motion

engine. It can be monitored in debug mode through the Connected Components Workbench

software when the motion engine is active, or through the user application as part of user

logic. It can also be monitored remotely through various communication channels.

One MC_Engine_Diag instance is created automatically in the Connected Components

Workbench software when the user adds the first motion axis in the motion configuration. This

instance is shared by all user-configured motion axes.

Function Block and Axis

Status Error Codes

All motion control function blocks share the same ErrorID definition.

Axis error and function block error share the same Error ID, but error descriptions are

different, as described in

Table 27 on page 178

Data Elements for MC_Engine_Diag

Element Name

Data Type

MCEngState

UINT16

CurrScantime

(1)

(1) The time unit for this element is microsecond. This diagnostic information can be used to optimize motion configuration and

user application logic adjustment.

UINT16

MaxScantime

(1)

UINT16

CurrEngineInterval

(1)

UINT16

MaxEngineInterval

(1)

UINT16

ExtraData

UINT16

MCEngstate States

State Name

State

Description

MCEng_Idle

0x01

MC engine exists (at least one axis defined), but the engine is idle as there is

no axis is moving. The Engine diagnostic data is not being updated.

MCEng_Running

0x02

MC engine exists (at least one axis defined) and the engine is running. The

diagnostic data is being updated.

MCEng_Faulted

0x03

MC engine exists, but the engine is faulted.

Error code 128 is warning information to indicate the motion profile has

been changed and velocity has been adjusted to a lower value but the

function block can execute successfully.

Summary of Contents for 2080-L50E-24AWB







































































































































































































































































































































































































Search results

Summary of Contents for 2080-L50E-24AWB

Reviews:

Rockwell Automation 2080-L50E-24AWB, User Manual, Page: 177 / 390

Search results

Summary of Contents for 2080-L50E-24AWB

Reviews: