REA JET HR pro 2K User Manual Download Page 9

Page: 9 / 189

Instruction manual

Page 9 / 189

REA JET HR

pro

2K / 4K

V 3.5x_001 28.05.2015

Warns against dangerous electric voltage.

This symbol indicates a hazardous situation as a result of
electrical voltage.

Risk of hazardous vapors

This symbol indicates potential

health risks

as a result of

solvents.

Fire hazard
Open fire and heat are prohibited.

This symbol indicates a fire hazard.

Disposal of operating resources

This symbol indicates when special care must be given
when disposing of operating resources. Please observe the
respective material safety data sheets, legislation, standards
as well as local regulations.

Wear eye protection

This symbol indicates that

appropriate protective goggles

must be worn.

Wear hand protection
This symbol indicates that

appropriate protective gloves

must be worn.

Observe the instruction manual

References to this manual or other documents are marked
with a book.

Care instructions

This symbol is used to provide information on proper care
and cleaning.

Information

This symbol points to useful information that can simplify
operation and improve the production process.

Tip

This symbol offers handling advice.

●

Bullet point

Steps of an instruction

Summary of Contents for JET HR pro 2K






























































































































































































Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands

REA JET HR pro 2K, User Manual

Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands