REA JET HR pro 2K User Manual Download Page 165 | Manualshive

Page: 165 / 189

background image

Instruction manual

Page 165 / 189

Copyright © REA Elektronik

REA JET HR

pro

2K / 4K

V 3.5x_001 28.05.2015

Figure 224: Firmware Update

Firmware Update

The firmware update can be carried out via this menu item. A xxx.hru file is required for the
firmware update. This file must be stored on a USB storage medium, which is to be connected via
one of the USB connections to the

. Start the update with the start

element.
File selection on the USB storage medium is done via rotary knob.
Start the process by pressing the knob and following the menu instructions.

The update can be performed directly on devices with firmware
1.84 and higher. For devices with a lower firmware version, an
update has to be performed to version 1.84 first. Since version 1.84
is included on our delivery CD and it is available on our website,
this two-step process should not be very difficult.
Please reset your device to factory settings after each update.
Please note that all data will be deleted when resetting. Therefore
please perform a backup beforehand.

The USB storage medium must have the FAT16 or FAT32 format.

Please note that firmware updates can only be performed to high
versions. A downgrade to an older version is not possible. Please
consult your REA contact.

«
...
163
164
165
166
167
...
»

Summary of Contents for JET HR pro 2K






























































































































































































Reviews:

No comments

Related manuals for JET HR pro 2K

POVCAM AG-HCK10G

Brand: Gates Pages: 2

Brand: Oki Pages: 17

Brand: Oki Pages: 12

Brand: Oki Pages: 30

Brand: Oki Pages: 391

Brand: Safemate Pages: 12

Magicolor 2 Desklaser

Brand: QMS Pages: 60

Brand: Tally Pages: 53

T2265 SprintPro

Brand: Tally Pages: 30

Brand: Tamron Pages: 3

Brand: Tally Pages: 108

Brand: TallyGenicom Pages: 2

Brand: TallyGenicom Pages: 2

Southern Series

Brand: Warmington Pages: 2

Maintenence Kits

Brand: Generac Power Systems Pages: 1

Brand: NeuLog Pages: 4

Brand: Aroflora Pages: 36

Brand: Manfrotto Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands