REA JET HR pro 2K User Manual Download Page 111

Page: 111 / 189

Instruction manual

Page 111 / 189

REA JET HR

pro

2K / 4K

V 3.5x_001 28.05.2015

4.2.4 USB connections (A4)

Figure 145: USB connection on the front side of the housing

(=A4)

4.2.4.1.1

Assignment of the USN connection (A4)

Pin HR

Name

Value

I/O

Supply voltage for the external
USB device

5V DC

Data +

Data -

Mass

Mass

Table 16: Assignment of the USN connection

(=A4)

Figure 146: View of the integrated socket

4.2.5 Connection for a bulk system (A5)

Figure 147: Connection for a bulk system on the front side of the device (=A5)



REA JET HR

pro

has two USB connections to

connect USB mass storage devices.



With this connection a hub can be used to operate
several USB mass storage devices simultaneously.



REA JET HR

pro

supports the USB 2.0 standard.



The USB connection is located on the side of the
REA JET HR pro 2K/4K housing.



At this time REA JET HR

pro

does not support bulk systems
with connection to the REA JET
HR

pro



The connection is intended for
future systems.

Summary of Contents for JET HR pro 2K






























































































































































































Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands

REA JET HR pro 2K, User Manual

Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands