Radyne ComStream TIERNAN SE4000 Installation And Operation Manual Download Page 44 | Manualshive

Page: 44 / 161

background image

SE4000 MPEG-2 Contribution Encoder

Using the Front Panel

01-0934-401-B

3-11

2.

Select Video.

SE4000/SERVICE/VIDEO >

[INPUT] ENCODER VBI

3.

Select encoder. Press the Right button to move the brackets to Encoder. Press Enter.

SE4000/SERVICE/VIDEO/ENCODER 1/3 >

ENABLE = ON

4.

The enable menu displays. Use the up and down buttons to select On. Then press enter
to select.

SE4000/SERVICE/VIDEO/ENCODER 1/3 >

ENABLE = ON

3.7 Modulator Control Buttons

The two modulator control buttons, located at the far right of the front panel, affect the power and
form of the output IF transmit carrier from the encoder. Each button has an associated LED
indicator. Only one of the LEDs is illuminated at a time. These buttons cause the output carrier
to be one of the following:

•

Off

•

Carrier on - full-power CW (constant wave)

•

Modulate on - full-power modulated

A blinking LED indicates that the button is busy implementing its command. When the command
is executed the LED stops blinking. Command execution takes 5 to 10 seconds to complete.
Each time you press the button, even if the LED is blinking, the command is executed.

The purpose of the buttons is to allow fast and simple operation of the encoder when a DSNG
operator is coming up on a satellite or taking down a link.

«
...
42
43
44
45
46
...
»

Summary of Contents for TIERNAN SE4000


































































































































































Reviews:

No comments

Related manuals for TIERNAN SE4000

Brand: Rabbit Pages: 120

Brand: La Marche Pages: 18

Brand: Zena Pages: 12

Brand: Naxa Pages: 36

Brand: OCULUS Pages: 28

Brand: Kelvix Pages: 2

Brand: Patton electronics Pages: 16

Brand: Lampizator Pages: 32

Brand: Wacker Neuson Pages: 36

Brand: Vitek Pages: 32

VECTOPOWER VP600 Series

Brand: Aradex Pages: 114

Brand: Kostal Pages: 12

Brand: CYP Pages: 9

Vizionlink PCIE-VL-3120

Brand: TechNexion Pages: 2

Brand: Carbest Pages: 22

Brand: Bush Pages: 42

Brand: INVT Pages: 174

SC-TDC-1000 D Series

Brand: Surface Concept Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands