background image

Using a Remote Unit 

 

SE4000 MPEG-2 Contribution Encoder 

4-10 

 

01-0934-401-B 

3.6  Correcting Mistakes 

 

3.6.1  Selecting Options 

 
If an option is selected and the Enter button has not been pressed, use the Up or Down buttons 
to scroll to the correct option. 
 

3.6.2  Using the Keypad 

 
If a value is entered via the keypad and the Enter button has not been pressed, the following may 
be done: 
 

• 

Left button to delete the numbers and then enter the correct value. 

• 

Exit button which returns you to the previous menu level. 

 

3.6.3  Leaving a Parameter 

 
If the Enter button has not been pressed, a parameter can be left without modifying it by pressing 
either the: 
 

• 

Exit button which returns you to the previous menu level 

• 

Left or Right buttons which take you to the next parameter 

 
In either situation, the SE4000 will ignore any values entered and return the parameter to its 
original setting. 
 

3.6.4  After Pressing the Enter Button 

 
If you accidentally issue an incorrect parameter value to the SE4000, you can correct the error 
by: 
 
1. 

Selecting the correct option using the Up and Down buttons.  The parameter will begin to 
flash. 

 
2. 

Pressing the Enter button to set the correct option. 

 

 

Example:  

The following example describes how to move through menus and select options.  In 

this example the SE4000 video will be enabled. 
 
1. 

From the main menu select Service and press Enter. 

 

 
SE4000/SERVICE                                                          > 
                   
[VIDEO]       AUDIO         DATA         TABLES     
 

 
 

Summary of Contents for TIERNAN SE4000


































































































































































Reviews: