manualshive.com logo in svg

Proximus forum 523, Mounting And Commissioning Manual

Share
Download
Proximus forum 523 Mounting And Commissioning Manual Download Page 40

Interface Cards

38

Installation

Installing Interface Cards

Each interface card is connected to the main board via two sockets. 
Forum 523/524’s slots have the following characteristics:

●

There is no prescribed order for assignment. You can, for example, use an 
interface card in slot 2, although slot 1 is not assigned. 

●

Slot 1 is connected to a group of pressure terminals. The pressure 
terminals of the slot are given the same colour to make them easier to 
identify.

●

The slots are not identical. Interface cards can therefore not be used in all 
and any slots. Please see the overview under 

Position of the Interfaces

 

starting on page 39 for details.

Installing an interface card

To install an interface card, please follow these steps:

1.

Switch off the Forum 523/524. Open the device (see 

Opening and Closing 

Forum 523/524

 starting on page 33).

2.

To discharge, touch a radiator or another metallic installation connected to 
earth ground. Take the interface card out of its packaging. Check that it is 
the correct type of card. There is a label specifying the type on the 
connector.

label

handle here

handle here

1

2

Summary of Contents for forum 523





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands