ProMinent DULCOTROL General Operating Instructions Download Page 87

Page: 87 / 144

Minent

Page 87

Possible

values

Initial value

Increment

Lower value

Upper value

Remarks

Cell con-

depending on 0.0001/cm

0.0060/cm

0.1499/cm

cc can be

stant cc

sensor type

0.001/cm

0.150/cm

1.499/cm

adjusted for

used

0.01/cm

1.50/cm

12.00/cm

all mr over the

complete

area

The measured value can be calibrated by changing the cell constant to the actual conductivity
value (arrow keys).

Select “install. factor setting?” in the setting menu, note the set installation factor and then set

to 1.00

Select the ﬁ rst menu option in the “calibration cc” setting menu and press Enter

Press Enter when the measured value under “LF” is stable

“please wait!” appears for a few seconds, then the DULCOMETER

D1C displays the current

calculated cell constant

The new cell constant is accepted when you press Enter to exit the last menu option (“calibra-

tion cc: - cc = ...”). Exit this menu option with the back key if you do not want to accept the
new cell constant.

Select “install. factor setting?” in the setting menu and restore the installation factor noted

earlier.

Next, restore the temperature coefﬁ cient

of the water sample used

It is highly recommended that you check the conductivity of the calibration solution with

suitable reference metering equipment to be sure that the conductivity of the calibration
solution has not changed due to carry-over of liquid or evaporation.

Inductive Conductivity

Conductivity Calibration

Measurement

Parameters

100

S/cm

Permanent display 2
only with control
(w = setpoint)

D1C2-cond.-011-GB

Permanent display 1

mea val.
fd. fwd.
reg. val.

70 %

59 %

100

S/cm

1000

S/cm

Positive values of setting variable: Increase conductivity
Negative values of setting variable: Reduce conductivity

D1C2-cond.-040-GB

calibration cc

probe in buffer!

accept value?

1538

S/cm 8.54

calibration cc ?

PAR1

calibration cc

cc: 8.54 /cm

cond: 100

S/cm

calibration cc

cc: 8.50 /cm

please wait!

Cell Constant Calibration (cc)

D1C2-cond.-030-GB

Access to all setting menus can be blocked with an access code !

meas. parameter

setting ?

mr = meas. range

cc = cell constant

2000

S/cm

cc :

mr :

1106

S/cm 25,0

mr 2 : 2000

S/cm

cc 2 : 8.54 /cm

1106

S/cm 25,0

8.54/cm

BA_DR_002_02_09_GB_Cooling.indd 87

24.02.2009 11:56:08 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands