ProMinent DULCOTROL General Operating Instructions Download Page 100

Page: 100 / 144

Minent

Page 100

8.8.4

DULCOMETER

D1C Measured Variable Chlorine and DULCOTEST

CTE

Sensor for Total Chlorine, Maintenance

Controller

The

DULCOMETER

controller type D1C for the measured variable total chlorine is maintenance-

free.

Sensor

IMPORTANT

• Service the sensor regularly to avoid overdosing within a control system, due to

in cor rect measured value.

• Observe the current national regulations for maintenance intervals.

• Do not touch the electrodes or allow them to come into contact with greasy substances.

• Never attempt to clean the membrane with acid/alkaline solutions, cleaning reagents or

mechanical aids (brushes or similar).

Maintenance interval

based on experience are:

• Potable, industrial, process and cooling water: depending on the speciﬁ c conditions

(1-4 weeks)

• swimming pools:

weekly

• spa pools (whirlpools):

daily

Maintenance

Work

Check the sensor regularly for dirt, algae and air bubbles. As far as possible, avoid contamina-

tion of the membrane with solid particles, deposits etc. Eliminate air bubbles by increasing the
ﬂ ow rate.

Check the displayed sensor value on the controller regularly according to the DPD-4 method

using an appropriate chlorine measurement kit.

If necessary, recalibrate the sensor.

If calibration cannot be carried out properly, the membrane cap must be replaced and cali bra-

tion must be repeated.

Total Chlorine

BA_DR_002_02_09_GB_Cooling.indd 100

24.02.2009 11:56:10 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands