ProMinent DULCOTROL General Operating Instructions Download Page 14

Page: 14 / 144

Minent

Page 14

1.4

Proper

Use

•

The

DULCOTROL

measuring/control stations are only designed to measure or control liquid

metering media in accordance with the Identcode feature speciﬁ ed on the rating plate of the
measuring/control station.

•

The

DULCOTROL

measuring/control stations are not designed to meter or control gaseous or

solid media.

•

The

DULCOTROL

measuring/control stations may only be used in compliance with the

technical data and speciﬁ cations stated in these operating instructions and the operating
instructions of the individual components!

• You are obliged to observe the information in the operating instructions on the various life

phases of the DULCOTROL

measuring/control stations (such as assembly, installation, …)!

•

The

DULCOTROL

measuring/control stations may not be used for applications in the open.

• All other uses or modiﬁ cations of the DULCOTROL

measuring/control stations require the

prior written consent of ProMinent Dosiertechnik GmbH, Heidelberg, Germany.

•

The

DULCOTROL

measuring/control stations may only be operated by sufﬁ ciently qualiﬁ ed

personnel (see table below). The operator of the DULCOTROL

measuring/control station is

responsible for the qualiﬁ cation of the personnel.

1.5

Qualifi cation of the Personnel

Safety Chapter / Storage and Transport

Tasks

Qualifi cation

Mounting, installation, hydraulical

Qualiﬁ ed employee

Installation, electrical

Qualiﬁ ed employee

Commissioning

Trained user

Maintenance

Trained person

Troubleshooting

Qualiﬁ ed employee

Disposal

Trained person

Storage and Transport

CAUTION

• Before storing or transporting, the DULCOTROL

measuring/control stations must be

free from metering media and water!

• Only transport and store the DULCOTROL

measuring/control station in its original

packaging!

• Protect the packaged DULCOTROL

measuring/control station also against moisture

and exposure to chemicals and mechanical infl uences!

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

Environmental conditions for storage and transport of

measuring panel without sensors

Temperature

5 ... 50 °C

Relative humidity

< 95 % relative humidity, non-condensing

Sensors

Store and transport the sensors within the sensor-speciﬁ c parameters. For information on the
individual cases, please see the documentation for the individual sensors.

NOTE

If the DULCOTROL

measuring/control stations are stored together with the sensors as an

assembly, the storage and transport conditions should be adjusted to the component part
with the lowest resistance to external infl uences!

BA_DR_002_02_09_GB_Cooling.indd 14

24.02.2009 11:56:03 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands