ProMinent DULCOTROL General Operating Instructions Download Page 139

Page: 139 / 144

Minent

Page 139

Troubleshooting

CAUTION

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

• Please observe the safety data sheets for the media involved in your process!

NOTE

• With terminal box: A terminal diagram is enclosed with the documentation of the

DULCOTROL

measuring/control station.

Troubleshooting

Cause

Remedy

No or insufﬁ cient sample

Filter clogged

Clean or replace ﬁ lter.

water ﬂ ow

See manufacturer’s docu-
mentation

Sample water pump with no

Control and repair of the

insufﬁ cient function

electrical supply, if required.
See terminal diagram.

Mechanical causes:
See manufacturer’s docu-
mentation

Heat exchanger clogged

Replace heat exchanger

Malfunction of the pressure

Check, clean and replace,

reducer

if required, pressure reducer.
See manufacturer’s docu-
mentation

Clogging of the piping system Check and clean, if required,

piping system

Inadequate metering and

Controller with no or

Control and repair of the

control performance

insufﬁ cient function

electrical supply, if required.
See terminal diagram and
operating instructions of the
controller

Defective or inaccurately

See the operating instruc-

calibrated

sensors

tions of the sensor, chapter
“Troubleshooting”, and the
operating instructions of the
controller, chapter “Errors /
Notes / Troubleshooting”

Control and repair of the
electrical supply, if required.
See terminal diagram.

Inadequate composition

Please observe the safety

and/or concentration of the

data sheets for the media

metering media

involved in your process!
Check the quality and/or
quantity of the metering
media and adjust, if required

Incorrect assignment of the

Check the assignment of

metering media

the metering media and
correct, if required

BA_DR_002_02_09_GB_Cooling.indd 139

24.02.2009 11:56:12 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands