ProMinent DULCOTROL General Operating Instructions Download Page 21 | Manualshive

Page: 21 / 144

background image

Pr

o

Minent

®

Page 21

Mounting/Installation

5.3.1

Measuring

Panel

Install a mains cable at the terminal box or at the controller in case of only one controller.

Electrically install the ﬂ ow meter (cables are pre-installed at the controller).

5.3.2

Sample Water Pump

With terminal box: Connect the sample water pump to the terminal box in accordance with the

terminal diagram.

Without terminal box: Connect the sample water pump to the supply voltage as described in

its operating instructions.

5.4

Mounting of the Sensors

Depending on the Identcode (Identcode feature “Sensor assembly”), some sensors will be

delivered already installed in the ﬁ tting. If no sensors are installed, the holes in the ﬁ tting are
tightly sealed.
The following sensors are not delivered as installed because of their sensitivity but enclosed in
the original packaging of the DULCOTROL

®

measuring/control station.

• All pH/ORP sensors

• All amperometric sensors

The sensors for conductivity and temperature are pre-installed.

Before installing the sensors, the respective blanking plugs are to be removed from the

DULCOTROL

®

measuring/control station and the respective sensors are then to be installed. The

installation of the sensors is described in the respective chapter for the measured variable.

5.5

Hydraulic Test Run after Installation

Having completed the installation, a hydraulic test run of the DULCOTROL

®

measuring/control

station is to be performed.

• The sampling valve must be closed! Otherwise, sample water may leak!

• Check all screw ﬁ ttings before the ﬁ rst commissioning!

• Open the shut-off ball valve on the inlet and outlet side.

• The station must be hydraulically leak-proof. No liquids may escape.

Should liquid escape, the cause is to be identiﬁ ed and remedied.

BA_DR_002_02_09_GB_Cooling.indd 21

BA_DR_002_02_09_GB_Cooling.indd 21

24.02.2009 11:56:04 Uhr

24.02.2009 11:56:04 Uhr

«
...
19
20
21
22
23
...
»

Summary of Contents for DULCOTROL

















































































































































Reviews:

No comments

Related manuals for DULCOTROL

Brand: Harrington Pages: 8

Brand: Handicare Pages: 32

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Zolix Instruments Pages: 22

Brand: TA Hydronics Pages: 14

Brand: Jafar Pages: 10

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: National Instruments Pages: 2

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brand: Water Specialist Pages: 60

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Gecko Pages: 82

Brand: McIntosh Pages: 68

Brand: CALEFFI Pages: 8

Brand: Roger Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands