ProMinent DULCOTROL General Operating Instructions Download Page 44

Page: 44 / 144

Minent

Page 44

Cleaning the Membrane

IMPORTANT

• Before removing the sensor, switch off downstream control devices or switch to manual

operation. In case of sensor failure, an incorrect measuring value may be present at the
input of the control/meas ur ing unit and result in an uncontrolled metering in a control
circuit.

• Depressurise the system before removing the sensor! For this purpose, close the

shut-off valves upstream and downstream of the fi tting. When removing the sensor,
liquid might leak if the system is pressurised.

• Read the safety notes of the system operator before opening the DGM/DLG III!

If the membrane is contaminated and the sensor cannot be calibrated, try to gently clean the

membrane.
First remove the sensor.
Remove loosely adhering deposits

Rinse the membrane under a gentle ﬂ ow of cold water, remove lime deposits

For this purpose, immerse the membrane cap into a 1 % hydrochloric acid (e.g. over night).

Rinse the membrane cap with a lot of water.

Now,

ﬁ ll the sensor with electrolyte, let the sensor run in and calibrate again.

Replacing the Membrane

If a calibration is not possible even after cleaning or if the membrane is damaged, it has to be

replaced (see “Assembly”).

Ozone

BA_DR_002_02_09_GB_Cooling.indd 44

24.02.2009 11:56:05 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands