ProMinent DULCOTROL General Operating Instructions Download Page 94

Page: 94 / 144

Minent

Page 94

Total Chlorine

Fitting the sensor in

the in-line probe housing

Note also the instructions and safety guidelines in the operating instructions of the in-line probe
housing.

DLG III

Slide the O-ring from below over the sensor up to the clamping ring.

Insert the sensor into the DLG III.

Fix the sensor tightly by screwing in the plug.

DGM

Slide the O-ring from below over the sensor up to the clamping ring. Leave a ﬂ at washer inside

the DGM.

Insert the sensor in the DGM and screw on the plug until the O-ring seals. The clamping ring

determines the installation depth of the sensor.

8.8.2.2

DULCOTEST

CTE Sensor for Total Chlorine, Electrical Installation

General Safety Guidelines

IMPORTANT

Install in such as way as to ensure a totally reliable, uninterrupted power supply to the

controller. Too low a voltage supply can cause measuring failures, which may result in
dangerous overdosing within a control system.

The CTE 1-mA sensor has a passive 4-20 mA two-wire interface. The power supply is provided

externally or by the controller. When the sensor is connected to the DULCOMETER

D1C

controller the interface’s safety require ments are met automatically.

IMPORTANT

For electrical connection of the sensor to the controller, only use wires with a diameter of
4 mm.

Electrical

Installation

Turn the top part of the sensor a quarter of a turn anticlockwise and remove.

Remove the outer isolation of the cable for about 5 cm from the end so that the two wires

appear.

CTE 1-mA

Loosen the M12 threaded connector and guide the 2-wire cable into the sensor. Leave an

approx. 5 cm length of the 2-core measuring line in the sensor.

Strip the two wires at their ends and connect them to the terminal block by using the

screwdriver provided: 1 = plus, 2 = minus

Tighten up the M12 connector.

Insert the top part of the sensor right into the housing and turn the top part clockwise as far as

it will go.

Electrical

connection

sensor

1 2

5 cm

CTE 1-DMT

Insert the 5-pin plug into the socket.

BA_DR_002_02_09_GB_Cooling.indd 94

24.02.2009 11:56:09 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands