ProMinent DULCOTROL General Operating Instructions Download Page 43

Page: 43 / 144

Minent

Page 43

Ozone

* If the reference electrode is of a silvery bright or white colour, it must be regenerated. Brownish-grey or

yellow-green discolourations, however, are common.

The

DULCOMETER

D1C can be used to display the sensor current for a sensor which is electrically

connected. Please read the value in the ﬁ eld “Zero point” in the complete operating menu, see operating
instructions DULCOMETER

D1C, Ozone, Chapter 8 in the setting menu “Calibration ozone”. Do not

conﬁ rm by pressing the Enter key but exit the menu by pressing the Return key.

8.2.4

DULCOMETER

D1C Measured Variable Ozon and DULCOTEST

OZE

Ozone Sensor for Ozone, Maintenance

Controller

The

DULCOMETER

controller type D1C for the measured variable ozone is maintenance-free.

Sensor

IMPORTANT

• The sensor is to be regularly serviced to avoid any excess metering caused by a sensor

failure!

• Observe the valid national regulations for maintenance intervals!

• Do not touch the electrodes or bring into contact with greasy substances!

Maintenance interval

Daily/weekly, depending on application

Maintenance

Work

Check the reading of the sensor at the control unit using a suitable ozone measuring tool (e.g.

DPD 4).

If required calibrate the sensor again (see Chapter “Calibration”).

Reading of the
sensor is 0 ppm
and error
message at
DULCOMETER

D1C

controller “Check O

input” is displayed

Reading of the
sensor is 0 ppm
and the sensor
current is

3.0 – 4.0 mA

Reading of the sensor
is any and the sensor
current is larger than
20 mA**

Reading of the
sensor is unstable

Correctly connect sensor to

control unit

Replace measuring line

Return sensor

Check control unit with sensor

simulator (DULCOMETER

Simulator, order no. 1004042),
return if faulty

Note running-in period

Check water for interfering

substances and replace water,
if required

Calibrate zero point

Return sensor for regeneration

Check system, remedy fault,

repeat calibration

Tighten diaphragm cap fully

Return sensor

Check installation site and

change, if required. Change
procedure, if required

Return sensor for regeneration

Sensor connected to the control
unit with wrong polarity

Measuring line broken

Sensor faulty

Control unit faulty

Running-in period too low

Interfering substances in water

Zero point shifted

Reference electrode faulty*

Ozone content above the upper
measuring range limit

Distance between diaphragm and
electrode too large

Sensor faulty

Pressure ﬂ uctuations in the
sample water line

Reference electrode faulty*

Fault

Possible cause

Remedy

BA_DR_002_02_09_GB_Cooling.indd 43

24.02.2009 11:56:05 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands