ProMinent DULCOTROL General Operating Instructions Download Page 18

Page: 18 / 144

Minent

Page 18

CAUTION

• Metering media may be metered in excess.

• If the fl oat of the fl ow module gets stuck because of contaminations, the DULCOTROL

measuring/control station may meter in excess!

• Install a fi lter, depending on the type and composition of the sample water.

• If the circulating pump does not deliver, the DULCOTROL

measuring/control station

may meter in excess!

• Interlock the control via the potential-free contact of the circulating pump. If the cir cu-

lat ing pump is “OFF”, the DULCOTROL

measuring/control station goes to “PAUSE” via

the pause input of the controller.

• Alternatively, the metering pumps can be switched such that they only work together

with the circulating pumps.

5.1.1

Measuring

Station

The mounting height should be selected such that:

• the LCD panel of the control is well readable

• the cover of the controller can still be parked in “park position” (145 mm)

• there is still enough space below the in-line probe to carry out maintenance work (100 mm)

• there is enough space for the mounting of accessories beyond the panel

The following drilling dimensions are to be observed in accordance with the panel size:

Mounting/Installation

Number of measured variables 1

A 595

695

1000

B 745

695

800

C 555

655

960

D 705

655

760

BA_DR_002_02_09_GB_Cooling.indd 18

24.02.2009 11:56:03 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands