ProMinent DULCOTROL General Operating Instructions Download Page 22

Page: 22 / 144

Minent

Page 22

5.6

Installation of the Sensor (electrical)

The cable ends of the connecting lines are identiﬁ ed by measured variables. The identiﬁ cation is

made with cable markers at the cable end. These markers are assigned to the measured variables
as follows:

Mounting/Installation / Commissioning of the Sensors

Commissioning of the Sensors

WARNING

•

Hazardous

substances!

• Hazards from contact, inhalation or other contamination with/by substances or media!

• Observe the safety data sheet of the used substance/media.

• The operator of the DULCOTROL

measuring/control station is responsible for the fact

that the safety data sheets are available and up-to-date.

CAUTION

• The sampling valve must be closed! Otherwise, sample water may leak!

• The sample water may not contain any airlocks to guarantee reliable measuring and

controlling!
Should air be contained in the sample water due to processes, the air is to be separated
with suitable technical means.

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

maximum permissible operating pressure:

1 bar at max. 55 °C

Preparation

Retighten all screw ﬁ ttings and check for leakages.

Check the positions of all shut-off valves. The position of the shut-off valves must guarantee

that the DULCOTROL

measuring/control station is leak-proof and that the sample water

ﬂ ows.

Connect the mains plugs to their corresponding socket-outlets and switch on the power.

Measured variable

Controller

Sensor type

Cable

identifi cation

PHE

ORP

Redox/ORP

RHE

Conductivity, inductive

Conductivity

ICT

Pre-installed

Conductivity

Cool Control

ICT

Pre-installed

Chlorine

CLE, CTE

Bromine

BRE

Chlorine dioxide

CLO

CDE, CDP

Ozone

OZE

Hydrogen peroxide

PER

BA_DR_002_02_09_GB_Cooling.indd 22

24.02.2009 11:56:04 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands