ProMinent DULCOTROL General Operating Instructions Download Page 19

Page: 19 / 144

Minent

Page 19

Mounting/Installation

Install the DULCOTROL

measuring/control station as close as possible to the metering

station using hanger screws.

5.1.2

Accessories

With accessories: From the hydraulical point of view, install supplied accessories such as heat

exchanger, sample water pump, pressure reducer or ﬁ lter upstream of the DULCOTROL

meas ur ing/control station, observing the respective operating instructions.

Plugs (type depending on the surface and according to the plug manufacturer’s speciﬁ cations)

2 Hanger

screw

3 U-washer
4 Hexagon

nut

10 mm

1   Sample water pump (not in connection with pressure reducer)
2   Heat exchanger (water/water)
3   Filter
4   Pressure reducer (not in connection with sample water pump)
5   Temperature monitor with shut-off valve

Not included in delivery scope, to be installed by the customer at media temperatures > 55 °C

BA_DR_002_02_09_GB_Cooling.indd 19

24.02.2009 11:56:03 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands