ProMinent DULCOTROL General Operating Instructions Download Page 99

Page: 99 / 144

Minent

Page 99

Total Chlorine

Fault

Possible Cause

Remedy

* When the reference electrode turns shiny silver or white it must be regenerated.

Brown-grey or yellow green coloration is normal.

** The DULCOMETER

D1C can be used to display the sensor current when the sensor is built into the

system.
For this enter the complete operating menu (see Operating Instructions DULCOMETER

D1C, Chlorine,

Chapter 8). Access the “Calibrating chlorine” settings menu and only read the mA-value measured under
“Zero point”. Do not ﬁ nish the zero point calibration but leave the menu by pushing the branch back
button.

Measured value of
sensor is 0 ppm and
error message
“Check Cl input”
appears on
DULCOMETER

D1C

display

Measured value of
sensor is 0 ppm and
sensor current
is 3.0 - 4.0 mA

Measured value of
sensor is arbitrary and
sensor current is

greater

than 20 mA**

Measured value of
sensor is not stable

Sensor is connected to controller
with wrong polarity

Signal lead is broken

Sensor defective

Controller defective

Run-in time too short

Interfering substances which
consume chlorine

Zero point has shifted

Reference electrode defective*

Chlorine concentration exceeds
the upper limit of measuring
range

Distance between working
electrode and membrane too
great

Sensor defective

Pressure ﬂ uctuations in
sampling line

Reference electrode defective*

Correctly connect sensor to the

controller

Replace signal lead

Return sensor to ProMinent

Check controller with the sensor

simulator (DULCOMETER

Simulator, order no. 1004042,
return to dealer if faulty)

See “Run-in period”

Examine sample water for inter-

fering substances and remedy

Carry out zero point calibration

Return sensor to ProMinent for

regeneration

Check the whole system,

remedy fault and then calibrate
sensor

Screw the membrane cup

tightly onto the electrode shaft

Return sensor to ProMinent

Check installation position and

change the process if necessary

Return sensor to ProMinent for

regeneration

BA_DR_002_02_09_GB_Cooling.indd 99

24.02.2009 11:56:09 Uhr

Summary of Contents for DULCOTROL

















































































































































Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands

ProMinent DULCOTROL, General Operating Instructions

Search results

Summary of Contents for DULCOTROL

Reviews:

Related manuals for DULCOTROL

Brands by name

Popular brands