Pressure Systems NetScanner 9116 User Manual Download

Page: 141 / 143

Pressure Systems, Inc. Model 9116 User’s Manual

Page 132

www.PressureSystems.com

Appendix F

NetScanner™ System Products

Model Purpose

9116

16-channel Intelligent Pressure Scanner with Ethernet TCP/IP Host Port.

9022

12-channel splash-proof, ruggedized Media-Isolated Intelligent Pressure
Scanner with Ethernet Host Port.

9032/33

Pressure Standard Unit with Ethernet TCP/IP Host Port.

9034/38

Pressure Calibrator Unit with Ethernet TCP/IP Host Port.

9046

Intelligent scanner for thermocouple and RTD measurements

98RK

Scanner Interface Rack that holds up to eight (8) Model 9816 Intelligent

Pressure Scanners. Rack provides power, pneumatic connections and hub

circuitry for up to twelve (12) 10Base-T connections.

9816

Intelligent Pressure Scanner that requires

98RK

Scanner Interface Rack for

power, pneumatic connections, and hub circuitry.

90DC

Data Concentrator, containing power and 24 switched Ethernet ports,

connections to as many as 24

NetScanner

™

System

modules.

9096

Series 9400 Interface Cable.

9082

Interface cable for connecting

NetScanner

™

System

modules to switches

and

hubs.

9400/9401/9402

Media-Isolated Pressure Transducers for Models 9021 and 9022

Summary of Contents for NetScanner 9116
















































































































































Search results

Summary of Contents for NetScanner 9116

Reviews:

Related manuals for NetScanner 9116

Brands by name

Popular brands

Pressure Systems NetScanner 9116, User Manual

Search results

Summary of Contents for NetScanner 9116

Reviews:

Related manuals for NetScanner 9116

Brands by name

Popular brands