manualshive.com logo in svg

Pressure Systems NetScanner 9116, User Manual

Share
Download
Pressure Systems NetScanner 9116 User Manual Download Page 117

Pressure Systems, Inc.                                                                                        Model 9116 User’s Manual 
 
 

 

Page 108 

 

www.PressureSystems.com 

5.1.3.3  

Remove and Replace PC-323 (Daughter board) on PC-322 (Main PCB)

 

 
(1) 

Remove the two (2) Phillips-head screws that hold the PC-323 onto the PC-322 board.   

 

(

Figure 5.3a

) 

 
 

 

 

 

 
 
(2) 

Gently rock the PC-323 board back and forth to loosen it and then lift straight up to  

 

remove it.  Place the old PC-323 in an electrostatically-protected bag for possible repair  

 

at the PSI factory. 

 
 

 

 

 

 

(3) 

Remove the new PC-323 board from its electrostatically-protected container

.  

Ensure the  

 

nylon spacer is in place on top of the mounting bar and over the threaded hole.  (See  

 above 

photograph, 

Figure 5.3b

).  Align the two (2) 40-pin connectors and press the  

 

board into place. 

 

 

Remove Phillips-head screws 

(screw already removed) 

 

Figure 5.3a 

Removing PC-323 Daughter Board 

Nylon spacer 

Figure 5.3b 

PC-323 Daughter Board Removed froom PC-322 

Summary of Contents for NetScanner 9116
















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands