Pressure Systems NetScanner 9116 Page 71 User Manual Download

Page: 71 / 143

Pressure Systems, Inc. Model 9116 User’s Manual

Page 62

www.PressureSystems.com

The optional

ipaddr

parameter is normally unspecified, causing it to default to use

the IP address of the current TCP/IP connection.  That way the host need not
have to be aware of its own IP address.  This parameter is provided in case a
special host has multiple network interfaces and wants to use more than one.
When used,

ipaddr

requires four dotted numeric fields (

d.d.d.d

). Each

is a 1-3

digit decimal number in the range 0-255. The

ipaddr

= 255.255.255.255 is best

avoided, unless the UDP datagrams of streams are to be broadcast to all
network nodes.

Example:

●

Configure all streams to be delivered via UDP/IP protocol. Host expects the UDP

datagrams to arrive via port 7500. The IP Address of the current TCP/IP

connection is also used to send each UDP datagram.

“c 06 0 1 7500”

Read

response:

“A”

●

Configure all streams to be delivered via the default TCP/IP protocol.

“c 06 0 0”

Read

response:

“A”

Summary of Contents for NetScanner 9116
















































































































































Search results

Summary of Contents for NetScanner 9116

Reviews:

Related manuals for NetScanner 9116

Brands by name

Popular brands

Pressure Systems NetScanner 9116, User Manual

Search results

Summary of Contents for NetScanner 9116

Reviews:

Related manuals for NetScanner 9116

Brands by name

Popular brands