Porsche 2015 911 GT3 Cup Technical Manual Download Page 303

Page: 303 / 321

Maintenance

Clutch actuation

Racing Brake Fluid-325° from Performance Friction Brakes is used as clutch fluid.

Consumables:

Porsche spare part number: 991.355.960.8A

Brake fluid

Porsche recommends bleeding the system after each practice and changing the fluid

after each race.

•

Fill quantity: approx. 500 ml (17 oz)

Bleeding procedure:

•

Depress the clutch pedal 2 to 3 times and keep it depressed

•

Shortly open the vent valve – the clutch pedal has to be depressed and
should not be released

•

Close the vent valve again

•

Repeat this procedure 2 to 3 times

•

Check the fluid level on the fluid reservoir

Replacement:

•

Remove the old fluid out of the reservoir and fill with new fluid

•

Then proceed as for venting, perform the steps approx. 10 times and make
sure that there is enough fluid in the reservoir

Version: 16.12.2014

302

911 GT3 Cup (991)

MY 2015

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands