Porsche 2015 911 GT3 Cup Technical Manual Download Page 299

Page: 299 / 321

Maintenance

7.2

Fuel system

7.2.1

Fuel

Superplus, unleaded (min. 98 ROZ)

The ethanol content in the fuel may not exceed 26 %

(E26).

7.2.2

Fuel pump

The fuel pump is located in the tank.

7.2.3

Fuel extraction

A defueling valve is provided close to the tank filler neck to empty the fuel tank. Use

a special hose with a quick disconnect coupling for defueling. Connect the quick

disconnect coupling to the nipple of the tank filler neck in the front section. To start

the process, the fuel pump switches located on the center console have to be in

position

„Fuel Pump Service”

. The fuel pumps are is then powered for 120

seconds. If this is not enough time to completely drain the fuel tank, turn the switches

again from the middle position (pump off) to the “Service” position. Keep the fuel in

suitable containers!

NOTE

7.2.1.1

Version: 16.12.2014

298

911 GT3 Cup (991)

MY 2015

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands