Porsche 2015 911 GT3 Cup Technical Manual Download Page 196

Page: 196 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

4.11.4

Installing the windshield

Risk of material damage if the predetermined curing

time of the glue is not observed! In order to ensure

proper bonding, the following conditions have to be

met:

•

Do not put the vehicle into operation before
the end of the curing time!

•

Curing time: two hours

•

Temperature: at least 10 °C (50 °F)

•

Fixing time: about one hour

The glue material has an open time of 15 minutes. This

means that the glue should be applied and the part be

joined within this time.

To ensure complete mixing, squeeze an approx. 30
mm (1.2”) long adhesive bead of fresh material on a

piece of cardboard.

•

Check the depth stops.

•

Replace damaged or missing depth stops.

Prepare two-component glue for processing.

NOTE

CAUTION

4.11.4.1

Version: 16.12.2014

195

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands