Porsche 2015 911 GT3 Cup Technical Manual Download Page 213

Page: 213 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

Mounting the new part

The bottom cross member and the rivets at the upper end next to the strut dome are

used for positioning.

All surfaces that are riveted have also to be bonded with two-component glue.

Place and rivet the blind rivets connecting the new part to the body.

Make sure that two different rivet lengths are available.

Rivet connections through two sheets:

short rivets 3.0-6.5

Rivet connections through three sheets:

long rivets 5.0-8.5

The riveting points are shown below

4.15.1.18

NOTE

Version: 16.12.2014

212

Summary of Contents for 2015 911 GT3 Cup


































































































































































































































































































































Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands

Porsche 2015 911 GT3 Cup, Technical Manual

Search results

Summary of Contents for 2015 911 GT3 Cup

Reviews:

Brands by name

Popular brands